Support and foundation structures for wind turbines

The SKI engineering company engaged in supporting and establishing structures for onshore wind turbines. The offshore variants are found in Offshore wind turbines under a separate heading.

WEA-Stahlrohrturm
WEA-Stahlrohrturm
Hybrid tower - concrete shaft / steel tube section
Hybrid tower - Lattice tower / Steel tube section
Guyed WT with tubular steel sections
Tilt-Up Tower
WTG - lattice mast

The range of services includes static and dynamic structural analysis using numerical simulation tools for the following applications:

In addition to the design of conventional support structures, we are also available for the development and realization of new structures. For special applications of our calculation tools please contact us.

The development of the system size and power rating

The continuous development of even larger turbines is closely linked to the increase of the dimensions of the support structures. In GASCH & TWELE 2005 is a compilation of specific tower masses as a function of hub height to be found. The required tower masses rise according to the structural load in an approximately square with the hub height. For a prototype with 6 MW rated power production of the bottom tower section would be possible as pure tubular steel construction only with increased manufacturing and assembly costs, with the tower manufacturer come up against technical production limits in steel construction. For example, in most plants, the round rolls of heavy plates with a thickness up to 70 mm is not yet a limiting factor. During transportation to onshore locations, there are many road bridges because of limited vertical clearance of 4.3 m, a further restriction on the tower diameter.

Entwicklung der Anlagengröße und Nennleistung

With increasing hub heights and plant sizes pushes the previous standard solution as a conical tubular steel tower is reaching its limits. The rapid growth of mass-produced wind turbines in terms of rated power, the rotor diameter and hub height can be seen in Figure 2.3. While the rotor diameter of a wind turbine in 1982 was D = 15 m, in 2008 are now systems with up to D = 125 m and 5 MW available. Prototypes with even greater benefits are currently being tested.

Led as higher production and transportation costs for the tower diameter is greater than 4.3 m to alternative solutions, such as the reinforced concrete tower, which is produced on site with a climbing formwork. Alternatively, a few years since precast concrete towers for large hub heights, the lowest tower segments are transported upright and as part of shells to the site. 

If above concrete tower sections or steel tower sections are used, then one of these combined design variant to the category of hybrid towers.

To future larger plant types continue to run starting with steel supporting structures of the base of the tower, the Sandwich tower has been developed to increase the shell stability and load-bearing capacity. The transport problem for diameters larger than 4.3 m is to be solved by a novel manufacturing concept.

Services

SKI Ingenieurges. mbH accompanies these onshore developments with

Dimensioning of the monopile

Because of low oil and gas resources Germany has so far been no country with a strong offshore industry. This is now changing with the construction of offshore wind farms in the North and Baltic Seas. But not only the offshore wind turbines themselves, but also the support structures, foundations, submarine cables, transformer stations and masts are required. In addition there are shipyards for manufacturing, sea ports for logistics and specialized vessels for installation.

As offshore structures are mainly:

Offshore Platform - Transparent

SKI Ingenieurgesellschaft deals with support and foundation structures for offshore wind turbines. The onshore variants can be found under the separate heading onshore wind turbines.

Monopile
OWEA - Jacket
Jacket
OWEA - Tripile
Tripile
OWEA - Tripod
Tripod
OWEA - K-Jacket im Wasser
Suction Bucket
OWEA - Hexabase
Hexabase

A variety of support structures for offshore wind energy plants

Is there a single support structure that best meets all offshore requirements? In the opinion of SKI engineers, this is hardly possible because a variety of different site conditions (e.g. water depth, subsoil), climatic influences and turbine classes must be taken into account when designing these structures.  

SKI-Ingenieurges. mbH can support you with the following tasks within the scope of concept studies and BSH approvals

  • Design of tower construction (primary and secondary steel)
  • Design and structural analysis of transition piece or central tube node
  • Calculations for foundation structures
  • Dimensioning of driven piles
  • Calculation of grout connections 
  • Concepts for steel heavyweight foundations

There are the following design variants more detailed information:

Services

The SKI Ingenieurges. mbH accompanied these offshore developments with the following servic

SKI_Logo_600px_72dpi_rgb

Copyright © 2026 

SKI Ingenieurges. mbH
Mengendamm 12
30177 Hannover

Phone: +49 (0) 511 / 261847-0

Consulting Engineers

BWE Expert Advisory Board